HD9000 Setup using 3 LMB Antenna
________________________________________
Viewsat 9000 Setup Guide Using USB
------------------------------------------------

1. First you must download and unzip (extract) the .pgm from the Files section.

2. Insert your Memory Stick in your PC and either transfer the extracted .pgm file from your computer or you can extract it directly to your USB drive.

3. Insert the USB drive into your STB. (either rear or front - just make sure you enable REAR USB or FRONT USB in the menu - under USER SETTING - OPTION) If the STB doesn't recognize you flash drive, make sure the drive is formated FAT32.

4. In the Main Menu select System information and press OK
Select Receiver Upgrade and press OK
Go down to the bottom of the window, select USB and press OK
A new window opens with files. Select your pgm file and press OK.
**************************************
VERY IMPORTANT. DO NOT TURN THE POWER OFF
Let the receiver finish and reboot on its own!!!
**************************************

5. Select User Setting -> Parental Control.
Set Menu Lock to Off. Password is "0000"
Select User Setting -> Time Setting.
Set Time Mode to Auto. Set Time Adjustment to the GMT offset for your area
(-5:00 for Eastern, -6:00 for Central, -7:00 for Mountain, or -8:00 for Pacific).
Set Summer Time to Off for Standard Time or On for Daylight Savings Time.
Select User Setting -> System Settings.
Set Local Channel to On. Change Local Channel Region to your city or the closest one listed. Channels will be mapped to their normal local channel numbers.
Select User Setting -> Option.
Set Sort By SID to On.
Set Auto TP to On.
Set Auto Roll to All.
Set Full Channel Name to On.
Select User Setting -> EPG Setting.
Set EPG TP to E:12472 and N:12311.

6. The following assumes you have put 119 on port #1 and 110 on port #2. You should change these to the way you have wired and connected to your switch.
7. If you are using a 1000 antenna with 3 LMB’s use port 3 for Sat 129W
8. If you are using 1000 antenna with 3 LMB’s and have the 8PSK card installed Go to menu – system settings – ext tuner and turn on the ext turner

*****************************************

SETTING UP ANTENNA SETTINGS: (119)
MENU -- INSTALLATION -- ANTENNA SETUP

Scroll top line (RIGHT/LEFT arrow key) to ******** 7 119.0W
LNB Power ON
LNB Type STANDARD (LEGACY LNB) or ("OCS-DP" for PRO LNB) depends on what you have.
LNB Freq. 11250
22KHz OFF
TP Freq. 12239 (it will default back to 12224 -thats normal)
DiSEqc 1.0 PORT 1
Motor OFF (If none)
You should display ******** 7 119.0W in the top right of the display!!! If not, you don't have your ports setup correct or your dish is not aimed correct.
"EXIT" and "YES" to Save.

*****************************************
SETTING UP ANTENNA SETTINGS: (110)
MENU -- INSTALLATION -- ANTENNA SETUP

Scroll top line (RIGHT/LEFT arrow key) to ******** 6,8 110W
LNB Power ON
LNB Type STANDARD (LEGACY LNB) or ("OCS-DP" for PRO LNB)depends on what you have.
LNB Freq. 11250
22KHz OFF
TP Freq. 12224
DiSEqc 1.0 PORT 2
Motor OFF (If none)
You should display ******** 6,8 110W in the top right of the display!!! If not, you don't have your ports setup correct or your dish is not aimed correct.

*****************************************

If you are using 1000 antenna with 3 LMB’s and have the 8PSK card installed set up Sat 129. If not skip set up for 129W

*****************************************
SETTING UP ANTENNA SETTINGS: (129)
MENU -- INSTALLATION -- ANTENNA SETUP
Scroll top line (RIGHT/LEFT arrow key) to CIEL2
LNB Power ON
LNB Type STANDARD (LEGACY LNB) or ("OCS-DP" for PRO LNB)depends on what you have.
LNB Freq. 11250
22KHz OFF
TP Freq. 12282
DiSEqc 1.0 PORT 3
Motor OFF (If none)
You should display Ciel 2 in the top right of the display!!! If not, you don't have your ports setup correct or your dish is not aimed correct.
*****************************************

"EXIT" and "YES" to Save.

Repeat the above steps for all of the sats you have LNB's for...

"EXIT" to the MAIN MENU


7. Channel Scan (also from Installation menu)
Select Auto Scan
Press OK
You can change the sat you want to scan by using the F1 button and selecting the sat to scan. Press exit to get out of the sat selection menu.
Select Scan Start and press OK. Do this for all the Sats you have.

8. Exit and save the settings

9. Wait for Autoroll and watch TV