Welcome to N2News FTA Files Forums

hi jim I need help with k pro 1st install. first I have a different k donngle than the
one pictured . mine is black narrow longer, 2nd I didn't get a power cord or knull
cable. and dont know how to activate or initialize it . it is stuck solid red.

Here is a comprehensive HELP guide if your experiencing issues with connecting via your HUB.

First let's make things CLEAR. The HUB is NOT produced nor "sanctioned" by K-Box. K-Box simply produces FTA units, the HUB is a THIRD PARTY device with THIRD PARTY software.

Okay let's first distinguish there are THREE versions of HUBS. Each has their own version number.

If you look at the hub you will see a series of numbers which begin with:

08001
08002
08003
09001

09006, THIS IS a NEW version and does NOT ship with a power adapter, Power is supplied via the BLACK CABLE, It comes with ONE BLACK cable, which is used to activate AND to run ***.

They are all basically identical, the PRIMARY difference is 08003/09001 do NOT arrive pre activated.

So if YOUR hub came with BOTH a BLACK as well as white/grey/cream Serial cable then it is NOT pre activated.

If you have the BLACK cable then the FIRST thing you MUST do is activate your hub by connecting it via the BLACK cable to your PC, you must then LOAD the (p) file, found in the files forum into your hub to activate it.

Now let's assume your hub IS activated. The following steps will help you rule out potential problems and eliminate them as the cause of no connection.

- Be sure to use the BLACK cable for activation and for connecting the hub to the K1 PROdigy, the white/grey/cream cable is for connecting the Hub to the K-Box K1PLUS.

- TEST your LAN cable, on a PC, (disconnect current cable and try the one you use with your K-Box).

- Ensure the settings in the MENU under Installation -> Options are set to MODE -> NETWORK, and BOTH autorolls are set to OFF

- IF you are using version 08001 or 08002 version hubs, these "tend" to connect better using the STATIC settings with the DNS servers settings as 4.2.2.1 and 4.2.2.2. You may choose your OWN ip the first THREE sets of digits MUST mirror those of your router IE 192.168.1.X. the X may be a number of your choosing within the range of your network. IE 16, (BUT it MUST NOT be the same as ANY other device on your network, so you should check to see what IP's are currently in use on your network.

- version 08003/09001 seems to work fine on the DHCP settings.

- You may ALSO, (especially if your using MTS or ALIANT as a ISP) change the DNS server settings IN your ROUTER to the public DNS Servers of 4.2.2.1 and 4.2.2.2). These ISP's servers will NOT permit your K-Box to connect, if you use THEIR DNS servers.

- check that your serial cable is a RS232 STRAIGHT thru cable, for the K1 PLUS, and a NULL modem for the K1 PROdigy, and that it is good and functioning.

- check to ensure you are using the AC adapter that CAME WITH the hub, do NOT use any other adapter, this could render your HUB a door stop.

- There will soon be a NEW file released which will permit you to do a "factory reset" on the HUB. This file will simply return the hub to it's FACTORY settings but will NOT affect the "activation" status of the hub.


IF after doing all the above try the following:

Unplug Modem
Unplug Router
Unplug ANY wireless devices used with the K-Hub/K-Box
Unplug HUB
Turn k-Box off via the rear switch.

Wait at least 30 seconds then re plug each device IN the SAME order that you unplugged them IE modem first, router second.....

Then reboot, (turn on), the K-Box make sure the mode is set to NETWORK.

The above info IF followed correctly should correct 99% of ALL connection issues.

If you still can't connect, then ask in the forums for assistance.

There's no need to worry about the power supply & the serial cable for the KHUB, you have the new II version. It gets its power from the recvr and plugs directly into the back serial port. Works great just the way it was shipped to you.

thanks 4 the info trailhand. but since i got nothing but {connecting please wait}
I thought I had to activate it and since I didnt get any other instructions, or power
cable Im totally blind on this. now I don't know what to do. So any suggestions
be great from anybody.

for kbox rescan dn youll have them watch tv injoy

Here is the link for k hub activation with USB drive.

k1pro_201_20090625

Anything I discuss on the subject is strictly hypothetical and in theory, and on an educational basis. I DO NOT test or condone any illegall activity.

first of, thanks again 4 the info trailhand that help me relax. Second I got it going
by usb. Yes I do read . So I loaded and upgraded, and voila.. just like gskondal suggested. Again thank you all