Welcome to N2News FTA Files Forums

I have my nano2 set up and all is ok. I am trying to set up my brothers and all is the same but the Diseqc. port Mine works fine on port 1 Echo10/11 110W when we try to set his on port one we get no SQ reading. But if we put it on Diseqc 2 we get SQ 95 on both but only 130 Ch. and the screen on tv is black. He lives 80 miles north of me. When i hook his up at my home it works fine on port 1Diseqc with a lot of ch. I hope i did this right so it can be understood. Please help. THANK YOU...

these are the only settings you need

119
Lnb power=on
Lnb type=OCS-DP
Lnb frequency=11250
Transponder... 119=12239
22khz=off
Diseqc... 119=1

110
Lnb power=on
Lnb type=OCS-DP
Lnb frequency=11250
Transponder...110=12224
22khz=off
Diseqc...110=2

I DO NOT TEST.I DO NOT CONDONE ANY ILLEGAL ACTIVITY.ANY INFO THAT I SEEK OR PROVIDE IS SOLELY FOR EDUCATIONAL PURPOSES ONLY.USE AT YOU OWN RISK.USE YOUR STB FOR TRUE FTA CHANNELS ONLY

We tryed that and no luck. We only get a SQ 95 when we are on Disqc2 with Echo10/11 110W. If we put anything on Diseq1 there is no SQ just black no green and blue bars. Also you have LNB-OCS-DP what and where is this found? Is there a step by step so we can see if eveything is right. We must be missing something. We can not even get the info. ch. We must be doing something wrong. I have tv on mine he has nothen on his. Thanks again

put back to virgin state reload bin start over

Have you tried to re-aim his dish, is there obstacles in the line of sight. Rule of thumb you have approximately 30 degrees line of sight. For instance when you look at it from a side view are there any trees, buildings or such that would block the signal from reaching the dish at 30 degrees. I live on an acreage and had a similar problem had to cut half an acre of trees to get the line of sight. I just put in a tower now I have a huge yard now need a riding lawnmower wow this is an expensive habit.

what kind of dish are you using and are you using a switch?

I DO NOT TEST.I DO NOT CONDONE ANY ILLEGAL ACTIVITY.ANY INFO THAT I SEEK OR PROVIDE IS SOLELY FOR EDUCATIONAL PURPOSES ONLY.USE AT YOU OWN RISK.USE YOUR STB FOR TRUE FTA CHANNELS ONLY

If he is using a disequ switch i bet he has the ports reversed...Also 119w will show very weak strength untill you go to scan it and the menu pops up allowing you to change the tp freq to 12239Mhz as it is set to 12224Mhz by default....the signals will then skyrocket on that sat if set-up correctly....when you hit seach it takes up to 3mins for any channels to start scanning (almost looks like it is frozen) don't worry wait channels will start scanning if set right..

Remember to hit the THANKS button if my post was helpfull (Or annoying...hehe)

All my posts are for educational purposes only, If they appear to not be worded hypothetically it just means I'm bad at first, second, or third person tenses...I'm not very good at story telling...I do not condone or encourage any illegal activity of any kind.

i have the conazsat nano when i scan i can only get vertical and not horozinal please tell me why

What type LNB are you using?? some are known to cause this issue....Also try a blind scan...post settings also for each sat...

Remember to hit the THANKS button if my post was helpfull (Or annoying...hehe)

All my posts are for educational purposes only, If they appear to not be worded hypothetically it just means I'm bad at first, second, or third person tenses...I'm not very good at story telling...I do not condone or encourage any illegal activity of any kind.